Відео

Were do you get those tires

I Love Harbor Freight. Heres My 69" Set up! All Harbor Freight. ua-cam.com/video/fKDafyhd-i4/v-deo.htmlsi=yngXpCSnmxUJZCYX

Easy when you start the video halfway through the job 🤣🤣🤣🤣 polock for you

Nice job

Awesome customization. You gave me some great ideas for hacking my Kobalt Mini toolbox. Thanks.

Fajny film

Now Lowes has to make some miniature tools to go in it.

These are rated 275 horse power

Ordered and fitted one. Ironically same shipping damage. Planning to repaint it. For the money the difference is worth it.

What did you do with the Trans Cooler lines? Pinch them off? Cap them? If you didn't, how much trans fluid did you lose after you removed them?

great video! Can you list all the part numbers and where did you order?

Nice detail given the instructions come with no descriptive wording, only drawings. I could not find any information about the alignment pins anywhere else. A couple notes: I was able to remove the grommets from the door frame with my fingers - no tool required. They are somewhat flexible so once you pry one side up, keep pushing until it releases. The other note is that the orientation of the slot the key goes in needs to be such that the key goes in from the bottom. If the slot is upside down, you reach a point where you can no longer insert the key to tighten or loosen the rack. I think my rack had all mounting ends fully released allowing that piece on one mounting leg to rotate.

In America most people call your French wrench a crescent wrench

I find it funny that a lot of people say be careful of using these tools and accessories because they are cheap Chinese crap but they are forgetting that the stuff they buy from Amazon, Walmart, Target and 98% of everything everything else we buy is from China.

I haven't bought from aliexpress yet bit I do have the phillips bits and bit holders from Temu and they work perfectly.

PRO TIP: they sell plastic clamps at Harbor Freight and online that are specifically for clamping down line with fluid. They are basically like vise grips, except they fully are plastic (so they are less likely to tear rubber hoses) and the jaws are flat to fully seal the hose together when you ratchet them tight. I use a couple of these when changing out cooling or fueling components and usually don't lose hardly any fluid

This is a great tutorial, i just got them wrapped with a piano black automotive film wrap and they look fantastic and it cost 25 EUR

Why won’t mine tighten,one side does but the other side wont

Great video man!

This is exactly what I was looking for! My 2018 is beginning to peel and was hoping for an easy fix like that! It's only peeling on one side buy im going to do both since it seems that the other side will eventually do the same

Will i be able to attach Yakima bike or ski racks to these bars? How does it work?

Use this to hold random drill bits by the drill press.

For $3,500, you won the damn lottery with this amazing old muscle car!

hi I have a mercedes sl 300 cab model year 1993. my question is, when the car is cold it starts, when it is warm it cannot be started until it has been sitting for a few hours, then you can start it again. can you the error would be very grateful🙏

What brand is the yellow tool organizer ?

I just learned about the existence of these toolboxes today and I found your video. My daughter thinks she needs one of these in pink for her crafting supplies. I like your handle, latch, and the wire you added to keep the lid from opening the whole way. I see I'm going to have some DIY fun as part of the setup of her toolbox.

Man I wish you could add those to my toolbox. I don't have the tools and am not handy enough to add anything, including a handle. But love all your additions to the toolbox.

Question: I am looking to purchase a roof rack for my 2016 Prius. What brand is this one? I haven't finished the video, but based on different reviews on low noise, I wanted to purchase a Yakima or Thule. What brand is this one? Thank you!!! Also, How do you know how long the bars need to be when you're shopping?

Do you have the website where i can buy this?

❤great video and explanation

You need to change that headlight 😂

good car

I’ll use it for drag racing and drifting

I only watched, cause of the prime bottle .

This is the realist tool cart tour I’ve seen 😂 not like everyone else “flexing” their expensive power tools and rare/handy specialty tool that we “have to buy bc it’s worth it” Just a simple, cheap tool assortment of tools that get the job done! And a few that were on sale 😂(I’m guilty of buying purely bc they’re on sale)

Great video lad

Very thorough! Thank you!!

Really beautiful bike man

just picked up an 09, always owned cruisers, wow these things are fast!😂

Do you notice any reduction in cowl shake?

I would be very cautious of using those fuses for anything - or anything cheap chinese crap related to any kind of safety. Louis Rossmann recently released a video where he tested top ranked Amazon fuses, and none of them worked properly. A 2 amp fused only blew at 10 amps. ua-cam.com/video/B90_SNNbcoU/v-deo.html

Thats not a feeler guage set.. its for thread pitch

Good video

I just found your channel and subscribed. Nicely done, Brother. I hope you will do some after use videos. On well, everything works out for you. For the price you can't beat it 😅 Thank you and Merry Christmas to you and your family 😊

You think it's possible to replace the rails with like actual drawer rails? The stock ones kinda suck.

Nice

18:47.. the Gearwrench bits are good... they're better than alot of other that come in kits..☝️

building off of one of those blow molded all in one kits like the gearwrench is a great idea, I had no idea they fit perfectly. As an auto tech myself I would probably skip on as much SAE stuff as possible unless you know your going to be working on pre 90s or specialty vehicles and I would probably grab a set of Tekton wrenches for about $50. The Pittsburghs could end up costing a lot if a bolt rounds. However thats my 2 cents. My coworkers all have enormously expensive boxes but I found out that you can essentially stack those us general carts and make them a 10 drawer. I did that to mine when I outgrew the original configuration and it was really inexpensive when they go on sale for $190

Yo bro, Jesus loves you 💪🏼

Thank you for the video. Very informative!👍